Recent content by FPVwannaB

  1. F

    First full build F3 FC frustration

    HAH! I came to work and used a PC with "STM8 Flash loader demonstrator". I was able to flash the thing and give it the proper drivers so I could flash Betaflight. One board was bad too I think. Albert Kim has a video on how to unbrick so maybe...
  2. F

    First full build F3 FC frustration

    Yea, I have 2 of them, both have the same problem, guessing we are dealing with a driver problem here
  3. F

    First full build F3 FC frustration

    Cleanflight is a no go, and the boards are fresh and uninstalled, flashing first
  4. F

    First full build F3 FC frustration

    MacBook pro so I have some limitations. I can try that baud rate. I have the latest CP210 (maybe a reboot after install might help as I did reinstall them.
  5. F

    First full build F3 FC frustration

    STM32 Communication failed, wrong response, expected: 121 (0x79) received: 31 (0x1f)
  6. F

    First full build F3 FC frustration

    getting this in BF
  7. F

    First full build F3 FC frustration

    Got two of these: https://www.gearbest.com/flight-controller/pp_638475.html F3 ACRO 6DOF Flight Controllers. One has its boot pins bridged one does not. Can't seem to flash BF or even Cleanflight. It says in CF it needs an update but when I go to choose the version I pick SPRACINGF3 and the...
  8. F

    JJPRO P200 Troubles, help needed

    Figured it out by watching reviews, the said wire went somewhere else. Should have made a legend on paper.
  9. F

    JJPRO P200 Troubles, help needed

    I don't know about my luck lately... I was working on a problem with the VTX, which I am replacing, and when it was reassembled this began to happen, a long constant beep that does not end. It seems to be when I plug in ONE wire, without it no beep. Not sure what the log unending tone means...
  10. F

    GRAAAARRRRR!!!!! LIZARD95 Driving me nuts!!!

    Update, it seems that the props went off too, and only 2 were spinning. Banggood is sending a new ESC. Hope this gets it going again.
  11. F

    GRAAAARRRRR!!!!! LIZARD95 Driving me nuts!!!

    Turns out that this is a known issue. Ultimately I wish I had known this I would not have invested in it, frankly: https://www.rcgroups.com/forums/showthread.php?2927885-Can-t-stop-drift-issue-with-Lizard95 It is exactly as they describe here. I think the heading should be "Beware buying the...
  12. F

    GRAAAARRRRR!!!!! LIZARD95 Driving me nuts!!!

    Oh no problems there, I already arrived looong before I started FPV...
  13. F

    GRAAAARRRRR!!!!! LIZARD95 Driving me nuts!!!

    OK. SO. I got the FLYSKY version, bound it and got it set up for angle/horizon/airmode. All I use angle mode for is taking off and getting used to the craft, WHICH I HAVEN'T been able to do! It does not take off like my other quads, as in UP>(very little manipulation) HOVER. I have been TRYING...
  14. F

    broken antenna repair

    Well the Rx wasn't included in the auction, so getting anything was a bonus. This quad flies really nicely. As it stands the Rx is fine all pins intact for PPM, which is what matters. I am probably going to order 3 or 4 of those Rx soon. Thanks for the heads up...
  15. F

    broken antenna repair

    Well not HORRIBLE lol, I know "props off" but I wanted it to catch it lol.
Back
Top