Search results

Hi jackson, when i did the setup the toggle switch would not recognised (on the computer it has a 3 position switch but the transmitter only has 2 x 2 position switches), but if you switch the switch it shuts off power to the quad. the power to the cc3d is taken from the ESC's. At the moment...

Hi, Im using a flysky FS CT6B 6 channel transmitter the servos work ok when connected to the receiver but the cc3d won't arm (i think due to two of the single wire connectors are not connected ?)

Hi, Im using a 4 motor quad setup on the cc3d and want to control a pair of servos via the accessory controls, i have tried to connect the servos directly to the receiver but this stops the cc3d from arming, and when i connect to the cc3d there is no movement on the servos, (not looking for...

will get higher when i can afford a battery that i don't need a fly lead :( it dose restrict the flying fun though :) )

hi using some small turnigy tg9 (now fitted in the vid) looking to have them move a pin/rod via one of the acc twist controls. (looking to release something) will look into the mode setting. thanks for the info (first quad and first time with the cc3d so playing about with it )

second flight after adjusting the cc3d settings changes to the calibrate on power up turned off fly's better. just still need to get the servos to work without using the camera gamble any help will be grateful ps the wind was blowing a bit by the end

Hi, the transmitter is a cheep flysky fs-ct6b with a cc3d flight controller (needs setting up properly never done this before) motors are 2212 @ 1000kv with 10 inch 4.5 props

Hi all, well i got sick of making balsa replacement arms, so made a new one verson 2.0 :) this time its out of plastic electrical conduit now it weighs 795g so slightly heaver here is the first flight

and in my best Victor meldrew voice I DON'T BELIEVE IT the ESC and motor have just started working again :) :) :) sadly i will have to wait to test it till tomorrow as the wife has band me flying it in the house since i wiped out halve the xmas decorations and the tree :eek::D:D:D

Hi I've tried to reconnecting the plug and all i get is a pulsing beep about 1 second on and one second off. i have connected it to the receiver and still the same, other 3 are working fine on t cc3d and receiver :(

Hi all, Im back again needing help, I have had a slight mishap with my quad. I went to pick the thing up and diss lodged one of the control cables from a ESC. to the cc3d (all 3 Power/ 0 volt / and signal) while the battery was connected and unit armed. now the motor won't turn it just...

Hi all, can any one help, Im trying to get the 5/6 outputs on a cc3d to work but having no luck if i connects servo to the cc3d on output 5 or 6 it won't work but the quad will arm and fly. If i disconnect the receiver output 5 and 6 and connect the servo to the receiver the servo will work but...

Im after a little help, I was having a few issues with open pilot and was informed that librepilotd would help. so downloaded it to my mac and then to the cc3d, (including new firmware ) and now i have very little throttle control (its on full or off :( ) I've tried adjusting the throttle...

Which is more crash resistant ?

Hi all, Now i have build my first quad out of balsa wood and am slowly getting the hand of crashing it sorry i mean flying it. i am now looking at building a better frame. Im building a H frame 450mm x 450mm and have two options 1) aluminium tube ( 15x15x1.5 mm walls) 2) carbon fibre 12mm round...

Hi all, Now i have build my first quad out of balsa wood and am slowly getting the hand of crashing it sorry i mean flying it. i am now looking at building a better frame. Im building a H frame 450mm x 450mm and have two options 1) aluminium tube ( 15x15x1.5 mm walls) 2) carbon fibre 12mm...

well a bit of gaffer tape and glue i had another go. :) I did manage to hover it for about 20 sec then flipped it :confused:o_O try again tomorrow :D

Update, took it out in the back garden this morning, was going well till it shot up and flipped over :eek: smashing one of its legs :oops: time for a repair and make some spares :D

now the fun starts :) just weighed the thing 606g (less battery) with a span of 650mm (25 inch)