Search results

I have tried flashing it and resetting it by the boot pins multiple times, with old and new firmware, but it still won't connect to cleanflight. And I am flying a racer quadcopter, no camera though.

It worked, but I just tried to recalibrate the accelerometer and nothing happened, so I disconnected and now it wont connect again.

IT WORKED!!!!!! I had to use firmware from 2016 haha!! Thank you so much!!!!

Thanks! I will try with an earlier version, as it's an F1 board. Do you know how much earlier I will have to go for the firmware?? Also I don't think I downlaoded the VPN drivers. What are they and do you know how to download them??

This still doesn't work...

Hi, I have the naze 32 flight controller and can't seem to connect it to cleanflight. I have tried different USB's and a different PC. I think the issue may be the drivers but i'm not sure. It says ' Serial port successfully opened with ID: 1' then 'Serial port successfully closed' when I click...

I've tried that and I've tried a different computer, but it still won't work.

It's probably flashing because I need to calibrate my accelerometer as my flight controller isn't connected to the quad. But, I can't do this as I can't connect my flight controller to Cleanflight...

Hi, I was able to flash the firmware onto my naze 32 board and I reset it using the bootloader pins. The board now flashes green and blue, does anyone know what this means? I followed a youtube tutorial() and downloaded something onto my flight controller. HOWEVER, when I try to connect my...

Yes, I did but I got no response from it when I used the transmitter.

Hi, I have the naze 32 board. It was working a while ago, however ever since I have changed the receiver, the board shows a blue light and it will not connect to cleanflight. I think I have installed the correct drivers, as they are listed on cleangflight, but when I try and reset the board by...

Hi, I really need help with this as it has been bugging me for a few weeks now, so any help is much appreciated. I managed to build my quadcopter and it was all working until one of the antenna got chopped off and had to replace the reciever. After I replaced the reciever my flight...

I need a charger for my turnigy 1300mah 3s nano tech battery. I don't know what charger to use, help would be greatly appreciated.

I have fixed the problem, the wires don't connect very well to the naze, which i think is because of the soldering, but thanks for your help!

this is the naze http://www.banggood.com/DALRC-NAZE32-REV6-MPU6050-32-bit-6-DOF10-DOF-Flight-Controller-for-Multicopter-p-1020774.html . The 6dof one.

This is it: http://www.banggood.com/FlySky-FS-iA6-2_4G-6CH-Receiver-For-RC-Airplane-p-985684.html . And yeah there is a wire from each of the channels (except the B/VCC channel as that is for binding) to the naze 32.

I don't have the naza M lite and I don't think the FS- ia6 supports ppm either. Do you know what could be wrong with it at the moment?

I have built my first quadcopter, but i cant get my transmitter to work. The quadcopter has a naze 32 6dof flight controller and a flysky i6 transmitter with a flysky ia6 receiver and i have set it up as pwm. I have binded the receiver to the transmitter and can see that they are connected as...

Okay thanks so i need to connect all 6 channels? And also when i do this it still doesn't work.

I just put all the components of the quadcopter together and the motor are working fine when I test them on clean flight. However, I can't get the the channel mapping to work and I am not sure what the problem is. I am using the naze 32 6dof flight controller and the fly sky fs i6 transmitter...