Search results

I recently replaced a burnt out FC on one of my quads with the CL RACING F4S. I'm trying to get the smart audio working now. Does anyone know which pad on the FC the smart audio wire from the vtx should be connected to? I'm just now venturing into smart audio and don't know much about it.

So I got this rechargeable battery for my new Taranis QX7 in the mail yesterday and I'm a little confused as to how to charge it. I can't charge it with my big charger that I use for all of my quad batteries bc it doesn't have a main batt lead like a xt60 or jst, only a 2S balance plug. Can I...

After building and flying, building more than flying because I'm not so great at the flying part just yet due to the fact I work so much leaving very little time to fly. Ever since I started I've just been using the fs-i6 that came with my eachine wizard "ready to fly" when I bought it. Over the...

I finally received my Floss 2 frame in the mail today. Trying to decide which motors I want to use with it. I have a set of Brotherhobby Returner R5's (2306 2650kv) sitting around waiting for a frame. My question is..would these motors be too much for such a light build, will they work well with...

I've decided to finally make the swap from PPM to ibus, and considering the fact that I have a severe technological impairment..me and technology just don't get along, I'm not quite sure what to do. I use the Flysky fs-i6 on 3 different quads all of which I built, not bought RTF or anything, and...

So I finished installing the DYS F4 on my main, and favorite quad last night. Hooked it up to betaflight to flash the latest version of firmware just in case, then set everything up in configuration, setup osd etc..I spun up all 4 motors to make sure they were good (and all 4 did just fine.)...

Well, I had just purchased 2 dys f4's for both of my quads. Started installing the first one last night and within the first few minutes 2 of the solder pads fell off the board. Very upset about this considering it is supposed to be one of the best FC's on the market currently. I will be sending...

Well, I had just purchased 2 dys f4's for both of my quads. Started installing the first one last night and within the first few minutes 2 of the solder pads fell off the board. Very upset about this considering it is supposed to be one of the best FC's on the market currently. I will be sending...

I bought 2 of the dys f4 FC's the other day, they just came in so I want to start getting them installed on my quads. I'm using a Flysky fs-i6 TX with fs-ia6b RX running ppm. I have had a couple different people, who are much more knowledgeable than myself, tell me that the PPM signal pad on...

I bought 2 of the dys f4 FC's the other day, they just came in so I want to start getting them installed on my quads. I'm using a Flysky fs-i6 TX with fs-ia6b RX running ppm. I have had a couple different people, who are much more knowledgeable than myself, tell me that the PPM signal pad on...

So I recently bought an omnibus betaflight f3 AIO V1.1 FC to replace the broken SP F3 in my eachine wizard x220. OMNIBUS Betaflight F3 AIO V1.1 Flight Controller with Integrated OSD Barometer Support SD Card https://banggood.app.link/bAiqv4SMME Can anyone point me towards a wiring pinout that...

2 part question: what is the big difference between a regular lipo and a graphene lipo, and are they really that much better than regular lipos?

So I had a mighty crash, into an even mightier oak tree yesterday with my Eachine Wizard X220, which I've modified to the point only the FC and frame itself are factory parts that can with the quad. Now I can add the FC to the list of modifications because the original SP F3 that it came with...

So I had a mighty crash, into an even mightier oak tree yesterday with my Eachine Wizard X220, which I've modified to the point only the FC and frame itself are factory parts that can with the quad. Now I can add the FC to the list of modifications because the original SP F3 that it came with...

I've been wanting to add an OSD to my quad for a while but everytime I start looking for one it just all seems so complicated. Couldn't someone please point me in the right direction of an OSD system which doesn't take a rocket scientist or computer programmer to install and configure. Will be...

Hey there I'm still pretty new to the world of fpv and mini quads, but I've already gotten hooked on the hobby. Any opinions on which 5" frame is the best in the $60 and under range, secondly which esc's are the "best" on the market these days? I decided to build my first quad from scratch...

So I've been trying to decide which HD camera I wanted to run on my new build and finally decided on the runcam 3. When I got on banggood to order one I was highly disappointed when I found a message reading "this item can not be shipped to your country." Which leads me to my question: can...

I finally got my ARF Wizard X220 in the mail yesterday, which is my second quad not including a tiny whoop. The ARF version comes with one 3 wire lead power, ground, signal sticking out of the top which is supposed to go to the receiver from everything I've read and saw on you tube. I hooked it...

I ordered This transmitter a while back to use with simulators, then..a day, maybe 2 at the most after receiving it in the mail I bit the bullet and bought a complete RTF fpv mini quad setup which of course came with a radio so now I have this one just sitting around collecting dust. Still brand...

Hey there, I have just recently made the leap from cheap toy quads to real fpv quads. Not knowing any better I jumped on Banggood and ordered a RTF Eachine Falcon 180...huge mistake, never again will I order directly from China off any of those sites. I live in the middle of nowhere Mississippi...