Search results

f450 frame 980kv motors .looking to upgrade would like gps. new at this what should i buy. thanks

i need some advice. this is the probulem . 250 frame 12 amp blheli with bec. four e max 2300 kv motors. kk2 board.was using a cc3d board but switched to see if that was the trouble. no luck there. all motors spinning in right direction. now when the props are off all four motors spin up.at the...

i just build a 300mm quad. with 4 e max 2300c motors. 4 12 amp esc bl heli bec 1r sv and crius power board . now is where i get stuck.when i go into the cc3d board and adjust the motors without the blades on on the motors spin up. but when i put the blades on the number one will spin up. the...

advise please. can i use a 200 3s on a 300mm quadcopter that has kv 2300 motors.thanks]

need a little advice. installed a new orange r615x on my 450 quad. motors will not go to full power i am missing something. thanks. using a kk2.1.5 board. have the same orange r615x on my 550 with kk2.1.5 board no problem. thanks.

mpu6050 what exactly does it do. what effect does it have on a quadcopter. thanks

any advice on a battery charger that i can use to charge more than one battery at a time. looking at a imax 6b. thanks

advise on a charger that i use to paraell charge.

advice on paying my first go pro and gimbal. what should it get . thanks

on my kk2.1.5 board there is a two prongs .next to that it says batt . what is this for thanks.

Need some advice please. running 1100v motors kk2.1.5 board at this time using 2200 turniguy 2200 mah 20 30c discharge. i have found that two of the batteries have puffup and getting very hot to touch. i was wondering if i could use a 4000 mah. and would i need a new charger. i have a duratrax...

on the kk2.1.5 board its says battery volon the screen. right now it says zero where do i set it to alert me when the vol gets to low. thanks.

Fist let me say thank for all the advice you have given me. now. ref programing card i have a hobby king 20 amp esc black. i got my hands on turnigy ty-p1 will this card program my esc. and important is it to program them.

need a little advice on buying a esc pogram card i have a hk blue 30a and hk 25 black amp which one should i buy. they are both ubec type. thanks

Guys. i have a question. 450 quadcopter 980 kv kk2.1.5 fc dx6i radio. every know and then it will drop out of the sky . about ten feet off the ground and the battery is a full charge. could i have a bad kk2 board a bad radio. thanks in advance for your input.

f450 running 1.9 steven kk2.1.5 board it is flying good. my q is x650 f v4 running 1.8pro stevens kk2.1.5 if i use the same setting do u think the x650f-v4 will act the the same reason jam asking is the x650f v4 wants to flip forward upon lift off. thanks.

i have four new motors that came with a long shaft. do they need to be cut are not .thanks

new build hk 650 f 4 1100 kv kk2.,1,5 board. stevens 1.9 . the prob when i go to lift off it wants to tilt forward. any info will be helpful. thanks

advice please. running 1.9s firmware is there a different setting for self leveling on this from ware

could i get some advice on the self leveling setting. 450 quad in x 980 kv motors kk2.1.5 board. also once u set the settings on the kk2. board do u still use the tx trim tabs. thanks.