Search results

Ok so I reset my settings in cleanflight to default. Turned all settings off. Tried leds on their own. Still nothing without "save and reboot". However on a test flight this morn I noticed the leds blinking while flying. Why could this be? Voltage on the led strip is 4.2v when they are on and...

I have got my addressable leds up and running after having to put a diode inline. I have them on and working...kind of.... the only way i can get them on is to "save and reboot" my naze via cleanflight. then they come on and stay on and work fine. when i unplug the battery and usb and plug them...

can anyone spot a problem in my cli dump? i am getting really frustrated with this. The leds work great when i save and reboot via cleanflight but not once i disconnect and re connect battery???? Entering CLI Mode, type 'exit' to return, or 'help' # dump # version # Cleanflight/NAZE 1.12.0...

WS2812B Addressable RGB LED strip DC5V 32 60 144

Can anyone help please? Is it maybe a voltage problem? Should I change the diode from 4.7v to lower?? Thanks

Already watched it. It would be helpful if I could find the auto tune tab in cleanflight??

I have got my addressable leds up and running after having to put a diode inline. I have them on and working...kind of.... the only way i can get them on is to reboot my naze via cleanflight then they come on and stay on and work fine. when i unplug the battery and cleanflight and plug them back...

ok so i have spent a couple of evenings looking at auto tune in cleanflight......ormore specifically looking for auto tune. I beleive it should be under the modes tab, and to assign it a aux switch. Its not there!! can anyone point me in the right direction?

Hi, I've read a lot about pids and am starting to understand them. Having just built my first drone and done successful test flight I found that the default pids were massively off. it flighs ok after a bit of adjustments. It wobbles a bit when decending, should I increase I to solve this...

its doing my head in now, ive tried putting throttle to -100% in tx failsafe and also tried using the disarm to to stop motors when tx signal lost. i guess its def the naze 32 thats triggering the motors to spin when failsafe activates even though ive set it to 0 in the failsafe tab and have...

i tried it in clean flight via the failsafe tab and also on the cli, i just tried doing it on my tx as well, as above. still no difference. loses signal, motors stop for a split second then 10 seconds of low throttle, then off. i just want the motors to stop when it loses signal. someone please...

Hi can anybody help me. I am trying to set failsafe to completely cut motors when tx signal lost. when i test by turning tx off it goes into failsafe and low throttle mode for 10 secs. no matter if i set the failsafe throttle number to "0" or "less than min throttle" i get the same response...

What size battery would you suggest?

Also are mini esc's acceptable or substandard to normal esc?

Thanks the videos were a great help! I've posted a parts lost that needs checking under "first time build"

Hi thanks for all the help on the forum already. Here's my final parts list I hope? Would someone mind checking it will all be ok? Dys 1806 2300kv motors max current 7.6a 12a Simonk esc 330 size frame with build in pub Naze 32 rev6 full 10dof Turnigy 5200 mah 30-40c Suggestions on props maybe 2...

Thanks for your input. Will def go for this one!

Was thinking of a Flysky fs-t6 to keep costs down. I know something like a taranis is way better buy budget dictates.

Hi, I'm looking at building my first quadcopter and think I've got my head around what I want to build but some advice would be helpful. I'm thinking a 250 size racing drone with gps and fpv with telemetry combined in the video stream. Am I right in thinking that ardupilot is the best flight...